Inside Line: TecRMI

by

Brake pedal wrong, missing, loosened components

RENAULT CLIO III 1.2 16V

Reference number 4692D
Fault symptoms: Preventive measure for a brake light switch defect.
Causes: Production defect.
Remedy: Replace stop light switch. If a blue sticker will be present in the area of the suspension strut dome in case the action was already carried out and on this field B6 was checked.
Part number:
Brake pedal switch OE (82 00 276 361)
Label OE (49 39 031 070)

Brake-pedal_TecRMI

Procedure

Release the retaining clamp(s). (1) Remove footwell covering(s). (2) Disconnect electric connectors. (3) Rotate switch. (4) Demount switch. (5) Measure and note the dimension A.

Set value: 19mm Minimum dimension
If deviating from target value: Adjust brake-pedal switch.
Otherwise: No further work necessary.
Adjust brake-pedal switch.

Crankshaft sensor combustion knocking, starting problems

RENAULT CLIO III 1.2 16V

Reference number: 4664A
Fault symptoms: Engine does not start. Non-concentric engine running
Causes: Electrical cable broken. Crankshaft sensor is signal faulty.
Remedy:
Replace connector on the crankshaft sensor
Part numbers:
OE (82 00 673 203)
OE (82 00 673 202)
OE (82 00 300 322)
OE (82 00 652 822)

Procedure

Remove the crankshaft position sensor. Disconnect the crankshaft sensor plug. Cut off electric cable(s) at connector.
Install repair kit. Installation is in reverse order of removal.

Alternator damage, engine warning light is on

RENAULT CLIO III 1.5 dCi

Reference number(s): 4582A
Install repair kit. 0,5 h
Fault symptoms: Engine warning light is on, noises in the engine region.
Causes: Pulley of generator defective.
Remedy: Replace pulley of generator. Replace generator. (If required)
Concerns the following vehicles: Clio II, Clio III, Kangoo, Logan, Modus, Megane I, Megane II,Laguna I, Laguna II
Part number Alternator pulley (Old )
OE (82 00 113 636)
OE (82 00 113 636)
OE (77 00 110 616)
OE (77 00 110 616)
Part number Alternator pulley (new)
OE (77 01 476 465)
OE (82 00 113 636)
OE (77 01 477 689)
OE (77 01 477 689)

Procedure:

The pulley and, if necessary, the alternator need to be replaced once the alternator pulley has come loose or is damaged. (2)(4) Alternator pulley, accessory drive belt, tensioning roller as well as the tensioning roller screw need to be replaced if the alternator housing should not be damaged. (3) Alternator, accessory drive belt, tensioning roller and the tensioning roller screw need to be replaced if the alternator housing should be damaged.

Alternator-Pulley_TecRMI

Window lifter noises

RENAULT CLIO III 2.0 16V Sport

Reference number: 0892A
Fault symptoms: Window lift generates noises.
Causes: Production defect.
Remedy: Fit washer.
Washers OE (77 03 053 951)

Procedure:

Remove the front door panelling. Unscrew and remove the window lifter screw(s). (1) Fit washer(s). (2) Installation in reverse order of removal.

Window-washer_TecRMI

ECP BOSS WARNS OF BLOCK EXEMPTION ‘EXISTENTIAL THREAT’

Andy Hamilton rails against VM ‘mini monopolies’ and demands that the UK government and the CMA take action in face of ‘abuse’ of the rules

Read More

PRA BOSS CALLS FOR FORECOURT ‘PINGDEMIC’ EXCLUSION

‘Forecourt workers are essential and should be exempt from self-isolation requirements if fully vaccinated’, say PRA

Read More

YORKSHIRE EXHAUST SPECIALISTS SAY ‘YES’ TO AAG BUYOUT

Leeds-based firm had been a UAN member and employed over 60 people

Read More

NEW TRADE COALITION FORMED TO FIGHT BLOCK EXEMPTION THREAT

AFCAR comprises of bosses from four major UK trade bodies

Read More

HALFORDS TO HIRE 700 TECHNICIANS

Chain hiring following a busy year for vehicle mobile servicing and pedal cycles

Read More

Go to comments

Your email address will not be published. Required fields are marked *