PROMO: CORTECO EXPLODES THE GUIDE BUSHES ‘MYTH’

PROMOTIONAL CONTENT WRITTEN BY CORTECO

 

Clutch input shaft sleeves (guide/ bushes) and seals: essential, but are they really only available through dealerships? Corteco explodes the myth.

The first call for any replacement part is the local motor factor, but when it comes to a part such as a clutch input shaft sleeve (guide/ bush) and seal, most UK garages turn to dealerships.

Essential in clutch changes for many German, Italian and French-built cars, dealerships hold a virtual monopoly on aftermarket sales throughout the UK. But the fact is, they are not an OE supply only item.

Garages only think they are.

 

New direction

Split-open view of a guide bush

Until quite recently, for example, that’s precisely what they thought up at Almark Garage in Wirksworth, Derbyshire:

“We always sourced them through the dealers. It just seemed like the place to get them because it was associated more with the OE gearbox than the clutch,” says proprietor Mark Swift.

“Our problem was that once you’ve got the vehicle up on the ramp and the gearbox off, you couldn’t hang around all day. Sometimes service from the dealers leaves a lot to be desired, so it meant that we didn’t always replace them, even though we know they can be a source of problems with the clutch.”

Almark is fitting more, now, because the availability has improved.

“It was only when the motor factor came along about three months ago and pointed out that they now had them in stock that we switched over. They are not expensive to buy, but even so, they are half the dealership price. I have to say that the service they provide means we are now fitting more than we ever did,” he adds.

 

Guide/ bush function

When not in operation, the clutch release bearing withdraws and comes to rest on the shaft sleeve. The shaft sleeve can become pitted through wear and tear. A worn release bearing can catch on it, leading to misalignment problems that can cause the clutch to slip.

This accelerates clutch wear.

Inside the shaft sleeve is a rubber seal. This is designed to protect the clutch from ingress by gearbox oil. If the seal fails there are problems ahead. Seal failure is often related to debris generated by clutch wear.

 

Contaminants

Clutch ‘dust’ accumulates in the gearbox. If the dust accumulates on the shaft and on the sealing lip, the seal can be compromised. It can damage the seal and reduce operational life. A worn or damaged seal allows the oil to leak into the clutch housing. If this contaminates the friction plate, premature failure of the clutch is inevitable.

This leads to excessive slippage. Any excessive slip between the clutch and flywheel causes overheating. Soaring clutch temperatures increase the potential for failure.

Installation errors

After removing the clutch, the clutch input shaft sleeve (guide/bush) and seal is sometimes ignored or not considered for replacement. Three alternative views are:

  1. a) It is part of the gearbox, rather than the clutch
  2. b) It looks ok, so let’s save the customer money
  3. b) They are difficult to replace so are best left alone

Each of these constitutes an error of judgement that can expose the garage to an expensive rectification procedure and damage its reputation.

Best practice

Corteco, one of the world’s largest manufacturer’s of clutch input shaft sleeves (guide/ bush) and seals, says that although these components are highly reliable performers, they must be replaced when changing the clutch.

It adds that because so many garages have always sourced their replacement from dealerships, many motor factors are unaware of the demand.

Given that labour is the major cost of the clutch change and that the clutch input shaft sleeve (guide/bush) and seal is not an expensive part, garages would be inclined to change more of them if the parts were available. A campaign to raise awareness about aftermarket availability is under way.

Published by Greg Whitaker

Editor of CAT Magazine and an experienced motoring journalist @GregWhitaker5

Brembo buys Öhlins for £310 million

Brake giant acquires Sweden’s high-end suspension manufacturer

Read More

Denso product blitz brings 32 new parts

Japanese supplier launches new components for BMWs, Fords, Mercedes-Benzes and more

Read More

Melett expands turbocharger range

Variety of turbochargers and core assemblies launched for some of the UK’s most popular vehicles

Read More

Movers and Shakers: Yanmar CE appoints president for all-new region

All the latest changes from across the sector, including new roles, promotions, and retirements

Read More

Delphi launches Tesla servicing course

Course covers issues such as Tesla’s service mode, ADAS calibration and battery work

Read More

Go to comments

Your email address will not be published. Required fields are marked *